How do I upgrade my tonearm?

How do I upgrade my tonearm?

1. Step 1: Loosen Screws. Use a flat head screwdriver and loosen headshell screws located on the cartridge.
2. Step 2: Unplug the Wires. Next, unplug the tonearm wires.
3. Step 3: Install the New Cartridge. You’re ready to install a new cartridge now!
4. Step 4: Put the Cartridge Together.
5. Step 5: Align the Cartridge.

How do I know what Rega tonearm I have?

The RB300 can be identified by the combination of black arm tube / silver counterweight and the large VTF adjuster on the side of vertical pivot. Early models where fitted with a dense (but expensive) tungsten counterweight which was later replaced by a cheaper (and larger) stainless steel counterweight.

When should I replace my Rega belt?

Rega recommends replacing the belt on their tables every 4-5 years. If you’ve been enjoying your Rega table for longer than 5 years and haven’t replaced your belt, why not upgrade to one of these belts and improve the performance of your analog rig!

How do I update my turntables?

1. Upgrade your turntable cartridge. Replacing your cartridge is the very first port of call for a turntable upgrade.
2. Replace your MM cartridge.
3. Upgrade your turntable by replacing the platter.
4. Upgrade your turntable by replacing the platter mat.
5. Use a speed controller.
6. Record clamps.

What tonearm is on the Rega p3?

RB300 tonearm
‘RB’ tonearms In 1983, Rega introduced the RB300 tonearm on the Planar 3 tonearm whose one-piece die-cast aluminium-alloy tube is the core of all Rega arms.

Are Rega Tonearms good?

Rega tonearms and their variants are probably the best selling hifi tonearm in the world. It took the audio world by storm in the 80’s and continues to be the choice of many manufacturers for their medium priced turntables. Naturally, this gives the RB300 and its successors as many fans as it gives enemies.

How long does a Rega belt last?

We recommend changing the drive belt every five years to ensure optimum performance.

How long does a Rega turntable belt last?

The frequency with which you change out your turntable belt has a few varying factors. If you use your turntable almost every day for at least a couple of hours, then you are much more likely to need to change your belt more often. A typical turntable belt can last anywhere from 3 to 5 years or even longer.

When did Rega start making Planar 3 turntables?

The Planar 3 with heavier plinth and thicker glass platter followed in 1977. Rega’s early turntables originally came fitted with Acos built tonearms, but in 1983 the first RB (Rega Britain) arm appeared in the shape of the critically acclaimed RB300 and it soon became one of the best selling tonearms in the world.

How do you upgrade the tonearm on a Rega?

What The Rega Tonearm Upgrade Involves. The Rega tonearm upgrade involves removing the rear stub. This stub is easily unscrewed from the Rega arm. Origin Live replace the old Rega stub with a new stub (or you can do it yourself). The new stub is torqued onto the arm by a thin high tensile bolt.

What parts should I upgrade on my Planar 3?

There’s a thread about my Planar 3 upgrades here. It started with an arm upgrade, but I went on to upgrade sub-platter, platter, motor, Neo, cartridge, belt, bearing… so much that I had enough leftover parts to build another turntable for my nephew. Starting from scratch again, I’d prioritise a new sub-platter and platter, in that order.

Why is the rear end of a Rega tonearm a critical area?

There is a secondary reason why the rear end of Rega tonearms is an extremely critical area–the Rega counterweight represents by far the highest mass in the arm and affects the Rega tonearm performance significantly. The Rega counterweight is excited into resonance by the motion of the arm.